fiche technique du linatex hard wall slurry hose bend 808-PHB
fiche technique des caractéristiques du tuyau coudé Linatex 808-PHB
Contenu du document
Linatex® Hard Wall Slurry Hose Bend (808-PHB)
Technical Specifications
Applications
- Pumping and transfer of abrasive slurries under pressure:
- Mineral processing plants
- Sand and gravel plants
- Tailings lines
- Oil Sands
Installation made easy
The Linatex® 808-PHB hard wall slurry hose bend range is renowned for its robust design and performance in delivering outstanding wear resistance in critical high wear applications. Manufactured to the same high standard as our 808 hard wall slurry hoses, our formed hose bends are custom produced to your required internal diameter, bend angle, radii and centre line to face requirements. The hot-vulcanised manufacturing process provides a made-to-order formed hose bend that is designed to fit the application without the need for excessive flexing. And the inbuilt swivel flanges make installation extremely easy. Our Linatex® 808-PHB hard wall slurry hose bends are the product of choice for many customers.
Design Features
- Designed to achieve superior wear performance over traditional steel lined pipe bends
- Lining thickness can be increased without reduction in the internal diameter
- Available with an extensive array of diameters, bend angles and radii configurations and may be customised to your needs
- Available with Linatex®, Linacure® or Linard® abrasion resistant internal wear liners
Properties
- Nominal bores from 50mm (2”) up to 1150mm (45”)*
- 1.5D, 3D and 5D bends fully interchangeable with pulled steel bends**
- Operating temperature -30°C to +75°C (-22°F to +167°F)
- Safety factor of 4:1
* Custom internal diameters are also available.
** Product specifications are subject to regional variations.
Wear liner composition is critical to the performance of your Linatex® rubber hose. With over 90 years of rubber manufacturing experience, we have the expertise to select the best compound for your specified application. Our superior Linatex® rubber compounds provide your application with outstanding wear resistance and extended wear life. This is designed to achieve the lowest total cost of ownership for all our hoses. For more information, please refer to our range of Linatex® rubber technical specification sheets.
Typical Physical Properties - 3D Bends
| Nominal Bore (D) | Typical Wear Liner Thickness | Radius (R) | 90° (A) | 45° (A) |
|---|---|---|---|---|
| 150 mm (6 in) | 6 mm (¼ in) | 457 mm (18 in) | 607 mm (23.9 in) | 339 mm (13.3 in) |
| 200 mm (8 in) | 10 mm (? in) | 610 mm (24 in) | 760 mm (29.9 in) | 403 mm (15.9 in) |
| 250 mm (10 in) | 10 mm (? in) | 762 mm (30 in) | 912 mm (35.9 in) | 466 mm (18.3 in) |
| 300 mm (12 in) | 12 mm (½ in) | 914 mm (36 in) | 1114 mm (43.9 in) | 579 mm (22.8 in) |
| 350 mm (14 in) | 12 mm (½ in) | 1067 mm (42 in) | 1267 mm (49.9 in) | 642 mm (25.3 in) |
| 400 mm (16 in) | 12 mm (½ in) | 1219 mm (48 in) | 1419 mm (55.9 in) | 705 mm (27.8 in) |
| 450 mm (18 in) | 12 mm (½ in) | 1372 mm (54 in) | 1572 mm (61.9 in) | 768 mm (30.2 in) |
| 500 mm (20 in) | 12 mm (½ in) | 1524 mm (60 in) | 1724 mm (67.9 in) | 831 mm (32.7 in) |
| 600 mm (24 in) | 15 mm (? in) | 1829 mm (72 in) | 2029 mm (79.9 in) | 958 mm (37.7 in) |
Weir Minerals
Copyright © 2019, Weir Minerals Australia Ltd. All rights reserved. WEIR and WEIR (logo) are trademarks and/or registered trademarks of Weir Engineering Services Limited. LINATEX, LINARD, LINACURE and the LINATEX RED COLOUR are trademarks and/or registered trademarks of Linatex Ltd. WMD0143/201510
info.minerals@mail.weir
www.minerals.weir
