ENG - Isogate WS Series Spec Sheet.pdf

A wafer-style slurry knife gate valve designed for abrasive applications Using materials proven by our extensive experience and installation base in the slurry transport industry, Weir Minerals has developed the Isogate ® WS series wafer-style valve to deliver reliability and long term performance. Its unique design provides ease of maintenance and low overall ownership costs, delivering outstanding results. Continuous innovation in material, product design, engineering and manufacturing ensures that the Isogate ® knife gate valve range remains at the forefront of valve design. Minerals The Isogate ® WS series slurry knife gate valve is specifically designed for a wide range of tough, abrasive and corrosive applications. Open Position Only thick elastomer sleeves are in contact with slurry. No metal parts contact the fluid. Closed Position The gate is located in between thick elastomer sleeves, with full tight shut-off. Bi-directional Double Elastomer Sleeve Design Applications • Mining • Power utilities • Pulp and paper • Cement • Sand and gravel • Coal • Phosphate • Soda ash • Alumina • Mineral sands Size range 50mm (2”) to 600mm (24”) Maximum working pressure • 50mm (2”) through 400mm (16”) - 1034kPa (150psi) • 450mm (18”) through 600mm (24”) - 700kPa (100psi) Flanges 50mm (2”) to 600mm (24”) : ANSI B16.5 class150#. Other flange options available. Materials • Body: Cast ductile iron as standard. • Gate: 316 stainless steel as standard. • Other materials such as HASTELLOY C-276 alloy, alloy 2205 are also available. • Sleeves: Natural rubber as standard. EPDM and other materials are also available. • Yoke: Carbon steel. Actuator options • Bevel gear • Pneumatic cylinders • Hydraulic cylinders • Handwheel • Electric motor The elastomer sleeves are easily replaced in the field without disasse\ mbling the valve. Isogate ® WS Series Slurry Knife Gate Valve Technical Specifications Note 1: Dimensions provided are for information only. Certified drawings are recommended prior to construction. Note 2: Flanges are drilled and tapped to match ANSI B16.5 class 150#. Other flange options are available upon request. Pneumatic Cylinder Valve Dimensions SizeABCDMASS mm inmm inmm inmm inmm inkg lb 50 2527 20.7 1305.111 5 4.5502.0 15 32 80 3655 25.8 1505.9140 5.5582.3 23 50 10 0 4732 28.8 2168.5165 6.5582.3 32 70 150 6955 37.626210.3 2168.5672.6 50 10 9 200 811 5 7 45.632412.8 2168.5803.1 66 144 250 1014 74 58.039515.6 27010.6 803.1 150 331 300 121621 63.847118.5 32412.8 893.5 203 448 350 141838 72.452020.5 37514.8 893.5 261 576 400 162 0 11 79.260023.6 37514.8 10 24.0350 772 450 182141 84.364025.2 55021.7 10 24.04 19 924 500 202355 92.768827.1 62524.6 1305.1504 1111 600 242808 110.6 81332.0 60023.6 1305.1912 2 0 11 Hydraulic Cylinder Valve Dimensions Size ABCDMASS mm inmm inmm inmm inmm inkg lb 50 26 10 24.0 1204.71305.1 502.0 15 32 80 374 9 29.5 1505.91405.5 582.3 21 46 10 0 4693 27.31656.51656.5 582.3 27 60 150 6998 39.3 26410.42168.5 672.6 38 84 200 811 9 9 47.232412.82168.5 803.1 68 150 250 101514 59.638515.227010.6 803.1 10 3 227 300 121678 66.147218.632412.8 893.5 180 397 350 141868 73.552220.637514.8 893.5 202 445 400 162055 80.959023.237514.8 10 24.0300 662 450 182195 86.464025.255021.7 10 24.0 346 763 500 202394 94.369227.262524.6 1305.1423 933 600 242861 112.6 81432.060023.6 1305.1 74 0 1632 Handwheel Valve Dimensions Size ABCDMASS mm inmm inmm inmm inmm inkg lb 50 2509 20.0 2007. 9200 7. 9502.0 1226 80 3638 25.1 27010.627010.6 582.3 1737 10 0 4736 29.0 27010.627010.6 582.3 2249 150 6925 36.4 27010.627010.6 672.6 3373 200 811 5 6 45.5 39015.439015.4 803.1 55121 250 101440 56.739015.439015.4 803.1 72159 Bevel Gear Valve Dimensions Size ABCDMASS mm inmm inmm inmm inmm inkg lb 150 61062 41.84 1016.150019.7 672.6 57126 200 81326 52.24381 7. 2500 19.7 803.1 73161 250 101571 61.947518.750019.7 803.1 11 4251 300 121766 69.553020.950019.7 893.5 19 04 19 350 141938 76.355421.850019.7 893.5 2 10463 400 162145 84.458423.060023.6 10 2 4.0303668 450 182286 90.069527.4600 23.6 10 2 4.0379836 500 202433 95.880031.562524.6 130 5.145710 0 8 600 242914 114.7 85233.51000 39.4 130 5.17251599 B A C D B C A D A B C D A B C D A B B B C C C D A A A C B D D D Maximise safety, reliability and cost efficiencies with the purpose-built Isogate ® WS series valve Upper stem cover Actuation options include: handwheel, bevel gear, pneumatic, hydraulic, electric (handwheel model shown) Stainless steel stem Stainless steel gate guard Lockout pin open/close Single piece cast body Load distribution ring Stainless steel clevis pin Packingless top seal assembly including grease channels Heavy stainless steel gate with tapered tip Resilient sleeve with reinforcing ring x2 Flush plate (optional) Open Bottom Open bottom allows for the purging of large solids, and solids in higher concentration. The purging of solids stops when the gate is in the full open or closed position. Flushing Plate Flushing plate option adds flexibilty to the standard open bottom. This option also allows for periodic cleaning of the lower discharge vent and can allow flushing as needed. Body Options Design features • Robust construction ensures long service life • Two-piece elastomer sleeve design protects flow areas against corrosion • Wafer body, narrow pattern minimises space requirement • Field replaceable thick elastomer sleeves are easily replaced without disassembling the valve • Sleeves incorporate Linatex ® rubber technology, plus a wide range of elastomer compounds are also available • Bi-directional 100% bubble tight shut-off • Packingless design - no gate or stem packing • Full port design reduces pressure drop and turbulence, minimising wear • Suitable for use in abrasive slurry services with high percentages of solids • Open bottom allows for the purging of large solids, and solids in high concentration • No seat cavities where solids can collect and cause gate interference • Yoke design allows fitting for all designed actuators • Flush control option allows for periodic cleaning of the lower discharge vent and allows flushing as needed Note 1: Dimensions provided are for information only. Certified drawings are recommended prior to construction. Note 2: Flanges are drilled and tapped to match ANSI B16.5 class 150#. Other flange options are available upon request. The Isogate ® WS series heavy duty knife gate valve features an adjustment free packingless upper seal which eliminates the need to constantly tighten the packing to eliminate leakage. The upper seal design also features a set of lubrication channels that contain a gate lubricant. A thin layer of the lubricant is placed on the gate on each and every cycle. This provides for smoother gate actuation and increased sleeve life. Fittings are accessible to recharge upper seal while in service. * sizes 50mm (2”) through 400mm (16”) Adjustment Free Packingless Upper Seal* lubricant channels sealing lips Note: The diagram above features the Linatex ® premium rubber sleeve option. Copyright © 2017, Weir Minerals Australia Ltd. All rights reserved. ISOGATE is a trademark and/or registered trademark of Weir do Brasil Ltda.; LINATEX and the Linatex Red Colour are trademarks and/ or registered trademarks of Linatex Limited; WEIR and the WEIR logo are trademarks and/or registered trademarks of Weir Engineering Services Ltd. Certain features of the technology featured in this publication may be protected by pending and granted patents in the name of The Weir Group PLC and/or one of its subsidiaries. HASTELLOY is not a trademark of any company forming part of The Weir Group PLC. WMD0188/201703 Minerals www.minerals.weir isogate@mail.weir